Welcome, Guest. Please Login or Register
Dynon Avionics, Inc.
 
Welcome to the Dynon Avionics forum!
  HomeHelpSearchLoginRegister  
 
 
Page Index Toggle Pages: 1
Send Topic Print
Does anyone know what fault this image shows? (Read 1363 times)
Apr 13th, 2012 at 7:01pm

Tony V   Offline
Frequent Poster

Posts: 18
**
 
Hi everyone,

I am currently installing a Skyview and when I installed the transponder, I got this image appear on the bottom right of the screen. Does anyone know what it means and, more importantly, how I can fix it?

BTW - the transponder area on the very top of the screen has a big red x over it. Im guessing the two issues may be related.

Thanks
Tony Vaccarella
Sydney
 
IP Logged
 
Reply #1 - Apr 13th, 2012 at 7:02pm

Tony V   Offline
Frequent Poster

Posts: 18
**
 
Sorry here is the image....
 

photo_004.JPG (139 KB | 108 )
photo_004.JPG
IP Logged
 
Reply #2 - Apr 13th, 2012 at 8:02pm

Dynon Support   Offline
Forum Administrator
Dynon Employee
Dynon Technical Support

Posts: 13096
*****
 
That's the status of the TIS traffic system. Since you are not in the USA you should have traffic (TIS) turned off in the transponder setup menu which will make this go away.
 

Please do not use Private Messaging on forum to contact. For private support:
Email: support at dynonavionics dot com
Phone: 425-402-0433 (7am-5pm Pacific weekdays)
IP Logged
 
Reply #3 - Apr 13th, 2012 at 9:49pm

Tony V   Offline
Frequent Poster

Posts: 18
**
 
Thanks for the quick reply. I have turned OFF TIS but the image is still there. Any other suggestions please?
Regards,
Tony
 
IP Logged
 
Reply #4 - Apr 14th, 2012 at 12:42am

Dynon Support   Offline
Forum Administrator
Dynon Employee
Dynon Technical Support

Posts: 13096
*****
 
Do you have another traffic device configured in your serial ports? A Garmin 330 or a Zaon?
 

Please do not use Private Messaging on forum to contact. For private support:
Email: support at dynonavionics dot com
Phone: 425-402-0433 (7am-5pm Pacific weekdays)
IP Logged
 
Reply #5 - Apr 14th, 2012 at 4:09pm

Tony V   Offline
Frequent Poster

Posts: 18
**
 
I dont have any other traffic device at the moment. But Im having probs with the transponder in that in the Transponder setup page, its not found. I have check power, tried different ports, and checked Rx and Tx lines. Im wondering if the two issued are related?

Regards
Tony
 
IP Logged
 
Reply #6 - Apr 14th, 2012 at 8:33pm

jakej   Offline
Expert
Australia

Gender: male
Posts: 1439
*****
 
Tony

I'll call you tonight & we'll go through a few checks, too busy at moment to call now.

Jake J
 
IP Logged
 
Reply #7 - Sep 3rd, 2017 at 9:16am

VFRPilot   Offline
New Member
I love flying!

Posts: 4
*
 
At the risk of reviving a 5 year old thread...

I'm having the same issue on a new install.  The transponder is "Not Found" by the EFIS.  I've verified the transponder is connected correctly, at least 10 times.  I even bypassed the signal wires to rule out a break in the lines even though they have continuity from end to end.

I contacted Dynon tech support, they requested I send it back to them.  I got it back on Friday but they did not find anything wrong with the transponder.  I'll call them again on Tuesday, but am hoping someone here might have a solution or other ideas.

Brian
 
IP Logged
 
Reply #8 - Sep 5th, 2017 at 12:55am

vfr pilot   Offline
Frequent Poster
I love flying!

Posts: 25
**
 
How can there be two vfr pilots on this forum, I wouldn't have thought this could happen.
vfr pilot
 
IP Logged
 
Reply #9 - Sep 5th, 2017 at 1:51pm

Dynon Avionics   Offline
Dynon Official
Dynon Technical Support

Posts: 12723
*****
 
We'll reply on the other thread that you opened. Please only post in one place about a particular issue.
« Last Edit: Sep 5th, 2017 at 1:53pm by Dynon Avionics »  

Please do not use Private Messaging on form to contact. For private support:
Email: support at dynonavionics dot com
Phone: 425-402-0433 (7am-5pm Pacific weekdays)
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print