Welcome, Guest. Please Login or Register
Dynon Avionics, Inc.
 
Welcome to the Dynon Avionics forum!


  HomeHelpSearchLoginRegister  
 
 
Page Index Toggle Pages: 1
Send Topic Print
Odd oil pressure behaviour on two 912iSís. (Read 157 times)
May 31st, 2018 at 8:24pm

Z-Air   Offline
Frequent Poster
I love flying!
Edmonton, Alberta, Canada

Gender: male
Posts: 46
**
 
There are two identical pipistrel aircraft with 912iS engines and mt constant speed hydraulic props here in Alberta Canada that have very odd oil pressure behaviour that we cannot figure out. Wondering if itís possibly due to the oil pressure sensors or software at this point.

Symptom: oil psi is not constant on both aircraft, they both have good indicated pressure on the ground before take off, indicating around 40-50psi. I canít speak directly for the other owner as to exactly the specs he gets but we both see similar numbers. I see 30 psi at 6000-7000íasl and at 15,000í I got as low as 14 psi this week while crossing over the Rockies. The other pipistrel owner replaced his oil pump in hopes it would bring up the psi but it did not improve his pressure readings. So we are stumped at what this could be.

Anyone else out there seeing similar things on their 912is engines?† Both aircraft have the same dynon skyview 10Ē displays and sensor packs for the 912iS.

My next step will probably be to install an analog gauge to determine if the dynon is indicating the correct pressure. But the rotax guys here also do not know what would be causing this on both aircraft.
 
IP Logged
 
Reply #1 - May 31st, 2018 at 9:09pm

jakej   Offline
Expert
Australia

Gender: male
Posts: 1531
*****
 
The pressure that you are seeing on the ground - is that what is expected ? Hot or cold oil ?
If yes then I think the next check is what youíve already worked out, use a mechanical gauge ( calibrated is best) to confirm or not whether what is displaying on the Dynon is correct. 
The correct sensor type has been entered into Setup Menu I presume ?
 
IP Logged
 
Reply #2 - Jun 1st, 2018 at 8:03am

Z-Air   Offline
Frequent Poster
I love flying!
Edmonton, Alberta, Canada

Gender: male
Posts: 46
**
 
Hi Jakej,  Yes it's expected although i'm surprised at how the oil pressure changes on the ground too. At idle I have about 45 psi but at full throttle for take off the oil pressure climbs to about 70, i've never seen oil pressure fluctuate like this in any other aircraft.  The other pipistrel owner has same issue, so it's either wiring issue with the sensor, or the sensors are faulty, or maybe it's how pipistrel has routed the oil lines. We can rule out bad oil pumps and pressure spring since the pipistrel dealer has replaced this on his with no change.  I think we will have to install analog gauge to confirm it's not the actual oil pressure fluctuating and possibly a dynon sensor or software or wiring issue.
 
IP Logged
 
Reply #3 - Jun 2nd, 2018 at 2:20am

jakej   Offline
Expert
Australia

Gender: male
Posts: 1531
*****
 
If that is the case then Iím guessing itís a pressure system design issue however itís hard to know not being there 😉
Please post your findings here when you get a resolution to the issue  - it may help others too.
 
IP Logged
 
Reply #4 - Jun 4th, 2018 at 12:47pm

Z-Air   Offline
Frequent Poster
I love flying!
Edmonton, Alberta, Canada

Gender: male
Posts: 46
**
 
I'll be installing an analog gauge this week to verify the oil pressure against the dynon indicated pressure. Will post results.
 
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print